FUEL CONSUMPTION SYSTEM
The FLOMECĀ® Fuel Consumption System (FCS) is a complete fuel monitoring system that comprises 2x EGM positive displacement meters coupled with an F127 flow instrument for accurate measurement of fuel consumption rates and total fuel consumption. The FCS can accurately measure fuel consumption on combustion engines by correcting for temperature differences from the inlet to outlet of the engine.
Pulsating flow electronics, eliminating error due to fuel injection pulsation, coupled with integral PT100 resistance thermometers in Flomecās renowned positive displacement meters gives an accurate and economic fuel consumption measurement solution in both land and marine applications.
The Flomec Fuel Consumption System (FCS) is designed for monitoring diesel engines on ships, buses, trains, gen setsDesigned for MGO or Distillate engines the FLOMECĀ® Fuel Consumption System is a highly accurate monitoring system. Diesel engines operate with a fuel recycle that can be 3 to 5 times greater than the actual consumption rate.
Operating without temperature correction can give 1% error in thermal expansion in the distillate volume for 10Ā°C in temperature difference. When this error is multiplied by the recirculation rate it will be 3-5% in systems operating without temperature correction.The other feature of the system is overcoming the pulsating flow produced by fuel injection systems that results in false readings as meter rotors can oscillate over a flow sensor. The special latching sensor board means any reverse flow wonāt result in flow detection.
The highly accurate oval gear meters (typically Ā±0.5% over reading, 1% for FSC006) have inbuilt temperature measurement allowing the net use meter to correct for fuel expansion through the engine. The net use meter gives flow rate to monitor instantaneous fuel use as well as recording net use volumes to help with fuel consumption and fuel tracking.
KIT SELECTION
Kit Contents
- 2 x Aluminium EGM Series Electronic Flowmeters
- 1 x F127 Totaliser
- 2 x Meter Brackets
- 1 x Fuel Strainer incl. Connector
- Cable Glands
Kit Contents
- A more accurate basis for estimating your operating costs
- Emission reduction through better fuel consumption control.
- Increased engine life through reduced wear with more efficient operation
- Theft identification by matching consumption with fuel purchase
- Low maintenance due to the lubrication of the moving parts by the diesel and solid state hall effect sensors
- Includes pre-strainer on supply and return lines to ensure long life and reliable service.
- Usage monitoring to estimate run times under load and monitor costs.
Although each Fuel Consumption
Kit consists of the same items,
the size of the meter and the
process connections change
depending on the rate of flow,
which is a direct correlation to
the size of the engine.
A typical diesel fuel loop system
would on average have 3.5 times
more fuel in its line than what the
engine consumes at full load.
With this in mind, selecting the
right kit based on the engineās
power output is important to
ensure accuracy and the positive
displacement metersā longevity.
The graphs depicted here should
be used as a guide when determining
the size of kit is required.
EGM Flowmeter
| Specification | Description |
|---|---|
| Flow Rates | 0.50 GPH - 21.1 GPM (2 L/hr - 80 L/min) |
| Sizes | Ā 1/4" - 3/4" (6 mm - 20 mm) |
| Engine Power | 7.5HP - 5000HP (Contact us for larger engines) |
| Temperature Range | -40Ā°F - +176Ā°F (-40Ā°C - +80Ā°C) |
| Body Material | Stainless Steel 316 (Marine) or Aluminium (Land) |
| Rotor Material | PPS (Stainless Steel 316 for EGM006 meters) |
| Cable Length | 2 metres (can extend using cable connector) |
F127 Totaliser
| Specification | Description |
|---|---|
| Casing | Robust IP66/IP67 Field Enclosure |
| Display | 7 digit resettable total, 11 digit accumulated total with backlight |
| Required Power Supply | 8 ā 24V (dc) (back up power supply built in to save settings in case of power failure) |
| Temperature Range | -40Ā°F - 176Ā°F (-40Ā°C - +80Ā°C) |
| Output Options | Ā 4-20mA and Pulse output available |
Can't quite find what you're looking for? Let us work with you.
Chat to our team of applications engineers to see how we can design and adapt our flow measurement equipment to meet your requirements.
As a manufacturer, we have a long history of working closely with system designers and OEM's alike to develop custom flow measurement equipment to cater to a wide range of applciations.
